|
|
| Technobabble Post your general Need for Help questions here.
• Lossy or Lossless? Moderators |
 |
|
|
Thread Tools |
|
#1
2007-02-05, 02:23 PM
|
||||
|
||||
|
Drive not recognized by software
hey now! last week, i installed ONES and Foobar2000 for the first time, all was fine- no problems burning disks. bout 5 days later, i started up ONES to burn some disks and the program said there was no drive destination. so i shut it down and ran the roxio easy media creator(all updated) and there was the same problem. so for shits and giggles i uninstalled ONES figurin it might conflict with other software, shut down, and checked all the cables. started it up again, ran the roxio easy media creator and the same thing. my OS recognizes the drives and i can put disks in the drives with data on them and they will open. i have plenty of disk space, run windows xp, my master drive is a LiteOn LTR24102M and the slave drive is a Plextor7-16A. any help appreciated, thanks in advance
jim
__________________
When I was a kid I used to pray every night for a new bicycle. Then I realised God doesn’t work that way, so I stole one and prayed for forgiveness. dvd list... http://db.etree.org/jimoosh No members have liked this post.
|
|
#2
2007-02-05, 02:45 PM
|
||||
|
||||
|
Re: Drive not recognized by software
No doubt a software/.dll conflict. I would uninstall Foobar/ONES/Roxio...etc..
-then full reboot for registry to update > then just one software at a time back on and more reboots between installs. Less software is more. I had this issue with EAC..but thats a different fix altogether. No members have liked this post.
|
|
#3
2007-02-05, 03:56 PM
|
||||
|
||||
|
Re: Drive not recognized by software
no luck. i uninstalled all of the new software and the roxio. uninstalled the drives. and only reinstalled the roxio, tried to burn a disk, but same thing. anyother suggestions
__________________
When I was a kid I used to pray every night for a new bicycle. Then I realised God doesn’t work that way, so I stole one and prayed for forgiveness. dvd list... http://db.etree.org/jimoosh No members have liked this post.
|
|
#4
2007-02-05, 04:37 PM
|
||||
|
||||
|
Re: Drive not recognized by software
Check and see if there is a firmware update for the dvd drive.
No members have liked this post.
|
|
#5
2007-02-05, 05:07 PM
|
||||
|
||||
|
Re: Drive not recognized by software
both are fully updated, im wondering if its possible, that the LiteOn drive(master) has just burnt out its burning capabilities(is this possible?) affecting the dvd drive since it is the slave drive? if i switched the jumpers(Mater/Slave), would it affect my OS since or make any difference.i tried to send the files to the drive directly, and it would not let me send it to the D drive, but i could send it to the F drive, but couldnt burn it with the windows media player due to copyright BS. its a live show
 makes me think that the D drive is burnt out. i tried to do a system restore and it says could not be completed when rebooted. im fuckin baffled 
__________________
When I was a kid I used to pray every night for a new bicycle. Then I realised God doesn’t work that way, so I stole one and prayed for forgiveness. dvd list... http://db.etree.org/jimoosh No members have liked this post.
|
|
| The Traders' Den |
Similar Threads
|
||||
| Thread | Forum | Replies | Last Post | |
| software help - chinajoe | Technobabble | 1 | 2007-10-09 11:49 PM | |
| VCD to DVD software? - jessenr88 | Technobabble | 0 | 2006-08-10 08:08 PM | |
| Thread Tools | |
|
|
